Clone CT70 Fuel Tank Rubbers these are meant to mount onto the clone frames but can be modified by the customer to work on your build.
|
MSRP: $73.00
Price: $63.00
You Save: $10.00 (14 %)
CT70 REAR LUGGAGE RACK. All CT70s FRAMES however some year bikes have other items installed that it will not work with - some years require modification. There is a 6 3/4 inch gap for where the taillight sits. Please see full description for fitment.
|
Designed & Manufactured by Trailbuddy Inc.the front high mount fender bracket is designed to mount on the bottom side of the triple tree (steering stem) to mount our TB229- High Mount Fender to the 30mm Fork Assemblies (TB149 or TB167) or your stock fork
|
MSRP: $45.00
Price: $30.00
You Save: $15.00 (33 %)
Aluminum skid plate for clone engines available for a kickstart or electric start motor.
The total length is 12 7/8 in and 5.5 in wide and the curve up starts at 8.5 inches. The mounting spaces are at 4 1/4 wide
|
Chrome Frame Molding with mounting clips on the inside of the strip. This is the piece that covers the frame from the seat up to the triple tree area of the frame. With fit: CT70 1970-1994 and ST90 1973-1975. It is #8 in the diagram.
|
CT70 Seat Bracket Hinge- Lower Portion. This will fit CT70 1970-1994; CT90 1969-1979; and ST90 1973-1975. You will need to use your original mounting hardware or will need an 8mm flat washer, 8x16 bolt, M6 flat washer and M6 hex nut. It is #3 in diagram
|
CT70 Seat bracket/Hinge B for the front of the seat. Will fit CT70 1970-1994. The main seat hinge pin is discontinued from Honda- we recommend reusing your original pin. You will also need a 6mm hex nut and 6mm flat washer.
It is #4 in diagram.
|
Frame Grommet that mounts in the rear of the frame. You will feed the taillight wires through this. It is #3 in the diagram. Will fit CT70 1970-1979; Z50A 1970-71 (K1-K2), and CT90 1966.
|
Honda Grommet Wire Harness best to use with the stock harness.
Fits CT70 1970-1982 models.
This is #4 in the diagram.
|
Restore the factory shine with a superior detailer specifically formulated for the powersports industry
Cleans, polishes and conditions plastic, fiberglass and painted surfaces
Also effective as a light lubricant for cables and levers
12oz. cans
|
Taillight Bracket Bolt Kits
|
Trail Buddy designed steering stop, it is stronger and thicker than the original and will need to be welded on. Recommend welding it on before paint. See full description for welding tips.
|
UNI FILTER SKID PLATE FOAM
Thick, very coarse foam keeps mud and grime from packing between engine and skid plate and allows water to drain away
Foam block is 8" x 10" x 2" thick
Trim to fit any application
Made in the U.S.A.
|
Wire Frame Clamp
Holds the wires going from the frame to the headlight bucket
|
Wire Harness Clip/Guide helps keep your wire harness snug against the frame. Will fit CT70 1970-1979 and ST90 1973-1975. It is #7 in the diagram. Mounting hardware not included.
|
WIRE HARNESS RUBBER/GROMMET CLONE- this works great if you are converting to a 12v harness. The slot to thread the harness through is larger than the stock OEM one to accommodate a bigger harness.
| | |