Lower Fork Slide Bushing. Will fit: CT70/CT70H (1970-1971); and Z50R 1979-1999. It is #11 in the diagram.
|
Triple Tree/Steering Bearing Top Nut. Will fit: CT70 1970-1994; CT90 K1 1969; Z50A 1969-1978; and Z50R 1979-1999. It is #13 in the diagram.
|
Triple Tree/Steering Bearing Washer. Will fit: CT70 1970-1994; Z50A 1969-1978; Z50R 1979-1999; and CT90 K1 1969. It is #14 in the diagram.
|
Front Fork Pin Spring. Will fit: CT70/CT70H (1970-1971); and Z50R 1979-1999. It is #12 in the diagram.
|
Triple Tree/Steering Bearing Lower Nut. Will fit: CT70 1970-1994; Z50A 1969-1978; Z50R 1979-1994; and CT90K1 1969. It is #11 in the diagram.
|
Stock Gas Tank Gasket. Will fit the CT70 1972-1994.
It is # in the diagram.
|
Rubber for Front Fork Stopper this will fit the early model front fork systems of the CT70/CT70 H (1970-71) model. It will also fit the Z50 A 1969-1978; Z50R 1979-1999; and the QA50 1971-1975. It is #10 in the diagram.
|
Clutch Set Ring (102mm). Will fit: CT70 1970-1992; ATC70 1973-74, 1978-85; TRX70 1986-87; CT90 1966; QA50 1973-75; Z50A 1969-78; Z50R 1979-99. It is #14 in diagram.
|
Z50R 1979-1999 Carb Gasket Set. It is #11 in the diagram.
|
Clutch Adjusting Bolt. Will fit: ATC70 1973-74, 1978-85; TRX70 1968-87; CT70 1970-1982; Z50A 1969-1978; and Z50R 1979-95.
It is #8 in the diagram.
|
Inner Dowel between the crankcases (10x14). Will Fit: ATC70 1973-74, 1978-85; CT70 1970-94; ST90 1973-75; CT90 1966,1969-79; Z50A 1969-1978; and Z50R 1979-1999. It is #19 in the diagram.
|
8x12 Dowel Between the Head and Jug. It will fit on the CT70 1970-1994; ATC70 1973-74,1978-85; Z50A 1969-1978; Z50R 1979-1999; and CT90 1966, 1969-79. It is #11 in the diagram.
|
Air Cleaner/Side Cover Rubber Grommets. Will fit Z50A 1972-1978 and the Z50R 1988-1999. It is #11 in the diagram.
|
MSRP: $48.00
Price: $41.94
You Save: $6.06 (13 %)
The 4 Clutch plates plus the set ring for the CT70H and HK1 models. #12, 8,6,and 7 in the diagram.
Cheaper to buy them all than separately.
|
MSRP: $30.85
Price: $27.76
You Save: $3.09 (10 %)
Stock Throttle Rebuild Kit- all the parts you will need to rebuild a sloppy throttle setup, with a 10% discount. This doesn't include the throttle cable holder since that is included with a throttle cable. #'s 19,15,26 and 11 in diagram.
|
Inverted Forks Replacement Brake Pads these are the pads for the front calipers for our inverted forks.
|
Cam Chain Tensioner Arm will fit CT70 1970-1994; Z50A 1969-1978; Z50R 1979-1999; ATC70 1973-74, 1978-1985, and TRX70 1986-1987. It is #3 in the diagram.
|
CT70 Seat Bracket Hinge- Lower Portion. This will fit CT70 1970-1994; CT90 1969-1979; and ST90 1973-1975. You will need to use your original mounting hardware or will need an 8mm flat washer, 8x16 bolt, M6 flat washer and M6 hex nut. It is #3 in diagram
|
Cam Chain Tensioner Pivot will fit CT70 1970-1994; Z50A 1969-1978; Z50R 1979-1988; ATC70 1973-1974, 1978-1985; TRX70 1986-1987. It is #5 in the diagram.
|
Cam Chain Tensioner Roller. Will fit CT70 1970-1994; Z50A 1969-1978; Z50R 1979-1988; ATC70 1973-74, 1978-1985; TRX70 1986-1987. It is # 4 in the diagram.
|
Cam 28t Sprocket will fit a CT70 1970-1982; Z50A 1969-1978; and Z50R 1979-1991. It is #1 in the diagram.
|
Ignition Wire Clip. It is #5 in diagram. Will fit CT70 1970-194; Z50R 1986-1987. Mounting bolt not included. Will need to reuse your original one or will need to find a M6x20 screw.
|
Frame Grommet that mounts in the rear of the frame. You will feed the taillight wires through this. It is #3 in the diagram. Will fit CT70 1970-1979; Z50A 1970-71 (K1-K2), and CT90 1966.
|
Uni Foam Filter Stage 2 for Z190cc motor which will clamp directly to carburetor. Use outside pre-filter dry for dusty conditions or oiled for extremely wet conditions.
|
Replacement 12v DOT Amber Blinker Bulb select either a single or dual filament.
To be DOT compliant, amber bulbs PART #25-8057A, single filament, or #25-8067A, dual filament, must be used with clear lenses.
|
SUPER M 2-CYCLE INJECTOR OIL
Blended for use in injector systems
Low-ash, smokeless, ester-fortified synthetic blend exceeds JASO-FC, ISO-E-GD and API-TC specifications
Sold individually in 1 liter jugs
|
This spacer kit is designed to use w/ our CT70 Brake Lever by Trailbuddy if you are not the stock brake lever components on from the year 1969-79. The mounting peg is too long for just the brake lever. Later models have shorter peg so this isn't needed.
|
Screw for the Z50A Air Filter Band it is #12 in the diagram.
|
This is a replacement screw for either the air filter hose or the screw that holds the alternator to hold the lighting coils on. It is # 20/18 in diagram.
|
Replacement Gearshift Arm Spring. It is number 12 in the diagram. Will fit:
CT70 1970-1982
Z50A 1969-1978
Z50R 1979-1987
|